HSN / HS Code 72111300Rolled on four faces or in a closed box pass, of a width exceeding 150 mm and a thickness of not less than 4 mm, not in coils and without patterns in relief

*IMPORT UNDER THIS CTI REQUIRES COMPULSORY REGISTRATION UNDER STEEL IMPORT MONITORING SYSTEM(SIMS). REFER POLICY CONDITION NO.5 OF CHAPTER-72 AND DGFT NTFN 33/2015-20 DTD 28-09-2020 AND FURTHER CLARIFICATION,RESPONSES TO PARA (2.A.)RE-IMPORT OF GOODS OF STEEL FOR PACKAGING PURPOSES WILL NOT BE COVERED UNDER SIMS AS IT IS NOT PRIMARILY MEANT FOR VALUE ADDITION,RATHER BEING RE-IMPORTED FOR PACKAGING ONLY AND PARA(2.B.)IN BOTH THE CASES I.E.(I) IF THE STEEL/STEEL ITEM IS EXPORTED FROM DTA TO SEZ AND THEN IMPORTED INTO DTA FROM SEZ WITHOUT VALUE ADDITION, OR (II) WITH VALUE ADDITION,THERE SHOULD BE NO REQUIREMENT FOR SIMS REGISTRATION.(REFER DGFT POLICY CIRCULAR NO.38/2015-20 DTD 19-01-2022)* BIS STANDARD IS 2002:2009 IS APPLICABLE ON STEEL PLATES FOR PRESSURE VESSELS FOR INTERMEDIATE AND HIGH TEMPERATURE SERVICE INCLUDING BOILERS. BIS STANDARD IS 2041:2009 IS APPLICABLE ON STEEL PLATES FOR PRESSURE VESSELS USED AT MODERATE AND LOW TEMPERATURE SPECIFICATION. BIS STANDARD IS 2062:2011 IS APPLICABLE ON HOT ROLLED MEDIUM AND HIGH TENSILE STRUCTURAL STEEL EXCEPT FOR BARS AND RODS OF DIAMETER OR THICKNESS LESS THAN 6 MM AND STRUCTURALS BELOW (50 MM X 50 MM X 6 MM). BIS STANDARD IS 1079:2017 IS APPLICABLE ON HOT ROLLED CARBON STEEL SHEET, PLATE AND STRIP. BIS STANDARD IS 5986:2017 IS APPLICABLE ON HOT ROLLED STEEL SHEET, PLATE AND STRIP FOR FORMING AND FLANGING PURPOSES. BIS STANDARD IS 15647:2006 IS APPLICABLE ON HOT ROLLED STEEL NARROW WIDTH STRIP FOR WELDED TUBES AND PIPES. BIS STANDARD IS 11587:1986 IS APPLICABLE ON STRUCTURAL WEATHER RESISTANT STEEL. BIS STANDARD IS 15103:2002 IS APPLICABLE ON FIRE RESISTANT STEEL - SPECIFICATION. BIS STANDARD IS 15914:2011 IS APPLICABLE ON HIGH TENSILE STRENGTH FLAT ROLLED STEEL PLATE (UP TO 6 MM), SHEET AND STRIP FOR THE MANUFACTURE OF WELDED GAS CYLINDER. BIS STANDARD IS 15962:2012 IS APPLICABLE ON STRUCTURAL STEEL FOR BUILDING FOR STRUCTURES WITH IMPROVED SEISMIC RESISTANCE. BIS STANDARD IS 3039:1988 IS APPLICABLE ON SPECIFICATION FOR STRUCTURAL STEEL FOR CONSTRUCTION OF HULLS OF SHIPS. BIS STANDARD IS 9442:1980 IS APPLICABLE ON SPECIFICATION FOR HOT - ROLLED STEEL PLATES, SHEETS AND STRIPS FOR MANUFACTURE OF AGRICULTURAL TILLAGE DISCS. BIS STANDARD IS 15911:2010 IS APPLICABLE ON STRUCTURAL STEEL (ORDINARY QUALITY)-SPECIFICATION. BIS STANDARD IS 10794:1984 IS APPLICABLE ON SPECIFICATION FOR MILD STEEL WIRE FOR COTTER PINS. BIS STANDARD IS 8917:1978 IS APPLICABLE ON SPECIFICATION FOR STEEL PLATES FOR GALVANIZING POTS. REFER STEEL AND STEEL PRODUCTS (QUALITY CONTROL) ORDER, 2020[SO 4637(E) DATED 22-12-2020].* IMPORT OF SECONDS & DEFECTIVE PLATES IS SUBJECT TO VALUE RESTRICTION, PORT RESTRICTION AND PRODUCTION OF PSIC. PRICE RESTRICTION ON PRIME PLATES SHALL APPLY TO THE EXTENT SPECIFIED IN THE MADRAS HC ORDER DT 21/01/04 IN W.P NO 38864 & 38865 OF 2003. REFER POLICY CONDT NO 1, 2 & 3 OF CH 72.**THE STEEL IMPORTING MONITORING SYSTEM (SIMS) SHALL REQUIRE IMPORTERS TO SUBMIT ADVANCE INFORMATION IN AN ONLINE SYSTEM FOR IMPORT OF ITEMS AND OBTAIN AN AUTOMATIC REGISTRATION NUMBER BY PAYING REGISTRATION FEE OF RS. 1 PER THOUSAND SUBJECT TO MINIMUM OF RS.500/ AND MAXIMUM OF RS.1 LAKH ON CIF VALUE. THE IMPORTER CAN APPLY FOR REGISTRATION NOT EARLIER THAN 60TH DAY BEFORE THE EXPECTED DATE OF ARRIVAL OF IMPORT CONSIGNMENT. THE AUTOMATIC REGISTRATION NUMBER THUS GRANTED SHALL REMAIN VALID FOR A PERIOD OF 75 DAYS. THE REQUIREMENT OF ADVANCE REGISTRATION OF MINIMUM 15 DAYS FROM THE EXPECTED DATE OF ARRIVAL OF IMPORT CONSIGNMENT UNDER SIMS HAS BEEN ABOLISHED.(REFER DGFT NOTF NO.19/2015-20 DTD 07-07-2022)*